Roof Framing Calculator & Cuts
Mirage Interactive Ltd Tools
Rafter calculator app, roof framing: hip, valley, jack, birdsmouth cuts.
- Price
- $6.99
- No in-app purchases
- Updated
- Nov 17
- 2026 · v1.0.4
Screenshots
About Roof Framing Calculator & Cuts
Rafter calculator and roof framing calculator for common, hip, valley and jack rafters: type the pitch and run, get the lengths, plumb cuts and birdsmouth. Offline, no ads, no subscription, one price.
A rafter calculator with side cuts and backing angles for hips and valleys, 1:1 cut templates and a printable cut card. No account, paid once.
WHAT YOU CAN WORK OUT
Common rafter, birdsmouth and tail, hip and valley rafters for regular roofs, a jack rafter table at your spacing, and a cut schedule that lists the pieces of a job with their quantities.
CUT MARKS
Every result lists the length along the top edge, the plumb, level and seat cuts, and for hips and valleys the side cut and the backing, with the angle given from the edge and from the square. A diagram shows what each number means.
1:1 TEMPLATES
Print cut-angle templates at exactly full size from the member depth you type: plumb, seat, birdsmouth, hip cheek and jack side cut. Each page carries a 100 mm and 4 in scale bar so you can check the print with a rule before you cut.
TYPE IT YOUR WAY
Give the pitch as rise in 12, percent, degrees, or rise and run. Give the run, the span or the gap between plates. Type lengths the way you say them: 12 1/2", 1' 3 3/8" or 30 mm. Each field shows how your entry was read.
SAVE AND PRINT
Save jobs by name, reopen, rename or duplicate them, keep a backup file, and print a one-page cut card. Light, dark and high-contrast themes, and built-in help.
THE MODEL IS STATED
Each result says which model it uses: lengths along the top edge between plumb lines, run from the building line to the ridge center, the ridge deduction as half the ridge thickness, jack lengths to the center of the cheek cut. The steps in between are shown, not hidden.
WHAT IT DOES AND DOES NOT DO
It gives lengths and cut angles only. It does not check spans, member sizes, loads, notch limits, fastening or code compliance, and it does not do irregular roofs, dormers or unequal pitches. Hip and valley results are for regular roofs. Check the fit on a scrap piece before you cut the run.
PRIVATE AND SIMPLE
Works fully offline. No ads. No account. No data collected. Your jobs stay on your device. Paid once, with no subscription and no in-app purchases.
Questions, problems or ideas? Tap Feedback & support in the app or email [email protected]. We answer every message.
Made by Mirage Interactive.
A rafter calculator with side cuts and backing angles for hips and valleys, 1:1 cut templates and a printable cut card. No account, paid once.
WHAT YOU CAN WORK OUT
Common rafter, birdsmouth and tail, hip and valley rafters for regular roofs, a jack rafter table at your spacing, and a cut schedule that lists the pieces of a job with their quantities.
CUT MARKS
Every result lists the length along the top edge, the plumb, level and seat cuts, and for hips and valleys the side cut and the backing, with the angle given from the edge and from the square. A diagram shows what each number means.
1:1 TEMPLATES
Print cut-angle templates at exactly full size from the member depth you type: plumb, seat, birdsmouth, hip cheek and jack side cut. Each page carries a 100 mm and 4 in scale bar so you can check the print with a rule before you cut.
TYPE IT YOUR WAY
Give the pitch as rise in 12, percent, degrees, or rise and run. Give the run, the span or the gap between plates. Type lengths the way you say them: 12 1/2", 1' 3 3/8" or 30 mm. Each field shows how your entry was read.
SAVE AND PRINT
Save jobs by name, reopen, rename or duplicate them, keep a backup file, and print a one-page cut card. Light, dark and high-contrast themes, and built-in help.
THE MODEL IS STATED
Each result says which model it uses: lengths along the top edge between plumb lines, run from the building line to the ridge center, the ridge deduction as half the ridge thickness, jack lengths to the center of the cheek cut. The steps in between are shown, not hidden.
WHAT IT DOES AND DOES NOT DO
It gives lengths and cut angles only. It does not check spans, member sizes, loads, notch limits, fastening or code compliance, and it does not do irregular roofs, dormers or unequal pitches. Hip and valley results are for regular roofs. Check the fit on a scrap piece before you cut the run.
PRIVATE AND SIMPLE
Works fully offline. No ads. No account. No data collected. Your jobs stay on your device. Paid once, with no subscription and no in-app purchases.
Questions, problems or ideas? Tap Feedback & support in the app or email [email protected]. We answer every message.
Made by Mirage Interactive.
What’s new
Version 1.0.4 · Updated November 17, 2026
New: if something goes wrong, the app keeps a short error report on your device. The app never sends it: under Feedback & support you can read, copy or delete it, and if there is a report, "Report a problem" adds its newest entry to your email. Fixed: with large text sizes, you can now scroll the content of every dialog to read all of its text.