Conduit Bending & Offset Marks
Mirage Interactive Ltd Tools
Conduit bending marks, plus voltage drop, wire size and conduit fill. Offline.
- Price
- $4.99
- No in-app purchases
- Updated
- Nov 17
- 2026 · v1.0.4
Screenshots
About Conduit Bending & Offset Marks
Conduit bending calculator for EMT, offline, no ads, no subscription, one price: numbered marks to tape on the conduit for offsets, rolling offsets, 3- and 4-point saddles, kicks and 90 stubs.
Pick the bend, type what you measured, check the diagram, read the marks. Offline, no ads, no account, paid once.
BENDS
Offset, rolling offset, 3-point saddle, 4-point saddle, kick, 90 stub, back-to-back 90s, kick 90 and segment bends for large sweeps.
MARKS YOU CAN TAPE
Every result lists the marks in order, measured from the end of the conduit, with the bender reference to line each mark up with and the shrink you will lose. A live diagram shows what each number means.
YOUR BENDER
Enter the take-up, gain and centerline radius stamped on your bender, and rename its reference marks (arrow, star, rim notch) to match. Nothing is assumed about your bender: the built-in profile is an example with no numbers.
TRADE TABLE OR EXACT
See the trade-table figures (the rounded multipliers printed in bender manuals, at 10, 22.5, 30, 45 and 60 degrees) next to exact geometry, and with your bender radius when you enter one. When a figure is not available the app says so instead of guessing.
TYPE IT YOUR WAY
Type lengths the way you say them: 12 1/2", 1' 3 3/8" or 30 mm. Each field shows how your entry was read. Inches and fractions or metric.
SAVE AND SHARE
Save bends by job name, reopen, rename or duplicate them, export a backup file, and export a one-page PDF bend sheet to print or share. Light, dark and high-contrast themes, and built-in help.
ELECTRICAL TOOLS
Voltage drop calculator: volts and percent lost along a copper or aluminum run, DC, single-phase or three-phase, at the conductor temperature you enter. Wire size calculator: the smallest standard size (AWG, kcmil or mm²) that keeps the drop under your limit. Conduit fill: how much of an EMT conduit your conductors take up, against the NEC limits of 53, 31 and 40 percent or your own. Bends between pull points: add up the angles and compare them with your limit. A planning aid, not a code check. Conductor diameters are approximate. NEC is a registered trademark of NFPA; this app is not affiliated with or endorsed by NFPA.
WHAT IT DOES AND DOES NOT DO
It gives numbers only. It does not say a layout meets any electrical code, check bend radius limits, or do ampacity, derating or box fill. The electrical tools are planning aids: resistance only with power factor 1, and their results are not a code-compliance determination. Bender values are the ones you enter. Bend one piece of scrap first and check it against the obstacle before you bend the run.
PRIVATE AND SIMPLE
Works fully offline. No ads. No account. No data collected. Your bends stay on your device. Paid once, with no subscription and no in-app purchases.
Questions, or a number that looks wrong? Use Help > Send feedback or Report a problem in the app. You can read and edit the email before it is sent.
Questions, problems or ideas? Tap Feedback & support in the app or email [email protected]. We answer every message.
Made by Mirage Interactive.
Pick the bend, type what you measured, check the diagram, read the marks. Offline, no ads, no account, paid once.
BENDS
Offset, rolling offset, 3-point saddle, 4-point saddle, kick, 90 stub, back-to-back 90s, kick 90 and segment bends for large sweeps.
MARKS YOU CAN TAPE
Every result lists the marks in order, measured from the end of the conduit, with the bender reference to line each mark up with and the shrink you will lose. A live diagram shows what each number means.
YOUR BENDER
Enter the take-up, gain and centerline radius stamped on your bender, and rename its reference marks (arrow, star, rim notch) to match. Nothing is assumed about your bender: the built-in profile is an example with no numbers.
TRADE TABLE OR EXACT
See the trade-table figures (the rounded multipliers printed in bender manuals, at 10, 22.5, 30, 45 and 60 degrees) next to exact geometry, and with your bender radius when you enter one. When a figure is not available the app says so instead of guessing.
TYPE IT YOUR WAY
Type lengths the way you say them: 12 1/2", 1' 3 3/8" or 30 mm. Each field shows how your entry was read. Inches and fractions or metric.
SAVE AND SHARE
Save bends by job name, reopen, rename or duplicate them, export a backup file, and export a one-page PDF bend sheet to print or share. Light, dark and high-contrast themes, and built-in help.
ELECTRICAL TOOLS
Voltage drop calculator: volts and percent lost along a copper or aluminum run, DC, single-phase or three-phase, at the conductor temperature you enter. Wire size calculator: the smallest standard size (AWG, kcmil or mm²) that keeps the drop under your limit. Conduit fill: how much of an EMT conduit your conductors take up, against the NEC limits of 53, 31 and 40 percent or your own. Bends between pull points: add up the angles and compare them with your limit. A planning aid, not a code check. Conductor diameters are approximate. NEC is a registered trademark of NFPA; this app is not affiliated with or endorsed by NFPA.
WHAT IT DOES AND DOES NOT DO
It gives numbers only. It does not say a layout meets any electrical code, check bend radius limits, or do ampacity, derating or box fill. The electrical tools are planning aids: resistance only with power factor 1, and their results are not a code-compliance determination. Bender values are the ones you enter. Bend one piece of scrap first and check it against the obstacle before you bend the run.
PRIVATE AND SIMPLE
Works fully offline. No ads. No account. No data collected. Your bends stay on your device. Paid once, with no subscription and no in-app purchases.
Questions, or a number that looks wrong? Use Help > Send feedback or Report a problem in the app. You can read and edit the email before it is sent.
Questions, problems or ideas? Tap Feedback & support in the app or email [email protected]. We answer every message.
Made by Mirage Interactive.
What’s new
Version 1.0.4 · Updated November 17, 2026
New: if something goes wrong, the app keeps a short error report on your device. The app never sends it: under Feedback & support you can read, copy or delete it, and if there is a report, "Report a problem" adds its newest entry to your email. Fixed: with large text sizes, you can now scroll the content of every dialog to read all of its text.